How to install artificial grass?

Here's a step-by-step guide on how to install artificial grass for a football field, whether it's a 5-a-side pitch or full-size professional field.

⚽ How to Install Artificial Grass for a Football Field

✅ Tools & Materials You'll Need

• Artificial turf rolls (with or without infill)

• Crushed stone or road base

• Geotextile fabric (optional)

• Turf glue & seaming tape

• Shock pad (optional for added cushioning)

• Turf infill (silica sand / rubber granules if needed)

• Turf cutter, compactor, rake, brushes

Step-by-Step Installation Guide

1. Ground Preparation

• Excavate the field area 10–20 cm deep.

• Create slope/drainage base (usually 0.5–1% slope for water runoff).

• Add base layer: Compact 10–15 cm of crushed stone or road base.

• Level & compact it using a plate compactor.

2. Optional: Install Shock Pad

• For professional or high-use fields, roll out shock pad underlayment for extra player safety.

3. Roll Out Turf

• Lay out turf rolls according to your field layout.

• Ensure pile direction is consistent for all rolls (they must face the same way).

• Leave rolls exposed to sun for a few hours to let them relax.

4. Joint the Seams

• Fold turf edges back.

• Lay seaming tape centered along the joint.

• Apply turf adhesive evenly.

• Press turf edges firmly together and walk over the seam to ensure bond.

5. Cut and Fit

• Trim excess turf around borders, goalposts, and corner areas.

• Ensure corners and lines are clean and straight.

6. Add White Lines (if not pre-stitched)

• Cut lines precisely from white turf rolls.

• Glue them into pre-cut grooves using the same seam tape and adhesive method.

7. Infill (if required)

• Spread silica sand and/or rubber granules evenly across turf surface.

• Use a drop spreader or infill machine for even distribution.

• Brush the turf fibers upright using a power broom or stiff brush.

8. Final Grooming

• Brush the turf again to ensure all fibers stand upright.

• Inspect seams and corners.

• Make sure infill is evenly spread and the surface is level.

Maintenance Tips

• Brush regularly to keep fibers upright.

• Remove debris or leaves.

• Replenish infill annually if used.

• Check seams and edges every 6–12 months.

Note:

For large or professional pitches, hiring experienced installers or turf contractors is highly recommended to ensure proper drainage, safety, and field longevity.

The installation of artificial turf is very simple for industry professionals, but for some buyers and customers, after all, there is no contact with professional training, and installation is still difficult, then vita VITA artificial turf Simply tell everyone about the installation steps of artificial turf:

1. Determine the level of the foundation, and clean the site foundation before installing the materials, especially some small gravel left in order to avoid the convex part during the installation process, so it will have a certain impact on the site use. Seriously, it will damage the lawn.

2. Draw a line. According to the size of the site, first use the ink line to play the site line on the ground, determine the center point, mark the point of the site, and the line position.

3. Move the lawn to the site and spread the lawn according to the marked location. When spreading the lawn, the problem to be noted is that the direction of the grass must be consistent, and then cut the lawn according to the drawings.

4. Start the installation, spread the lawn, place the splicing tape at the edge between each grass, and then brush the special turf glue on the splicing belt. Make sure that each turf can be closely connected without gaps.

5. Press the splicing place with a heavy object to prevent the occurrence of gaps. The splicing place can be placed in the granule bag.

6. Prepare the installation of the white line. Cut the green grass at the white line position according to the previously marked white line position, and then follow step 4 to install the white line.

7. Brush the lawn with a scrubber to keep it upright to prepare the rubber particles for quartz sand and artificial grass.

8. Fill the quartz sand with a particle filling machine, wherein the amount of quartz sand is generally 25 kg / square meter, and then the rubber particles are generally 5-7 kg / square meter.

9. The installation is complete.

If you have any questions about the installation of any other artificial turf, please feel free to contact the VITA artificial turf, we have a professional installation team to give you professional advice.